paolotrt Pubblicato: 21 Maggio 2011 Segnalazione Share Pubblicato: 21 Maggio 2011 Salve, sono nuovo di questo forum. E da ieri sera che non dormo per cercare una soluzione per resuscitare il mio nokia n8. Ho eseguito un flash con phoenix scaricando il firmware (che ho scoperto essere Vodafone UK)da navifirm ma a un certo punto il programma mi ha dato un errore e da allora il mio nokia si è spento. Tenendo premuto il tasto di avvio ogni tanto da una vibrazione oppure tenendolo premuto ogni tanto ne da tre di vibrazioni. Anche con l'hard reset non riesco a farlo ripartire. Ogni tanto quando collego il caricabatterie al nokia o la usb mi lampeggia il led bianco laterale. C'è un modo per farlo riprendere senza mandarlo in garanzia? vi prego aiutatemi sono stato 11 ore consecutive a pc per cercare una soluzione. Link to comment Condividi su altri siti More sharing options...
rapidshare Pubblicato: 21 Maggio 2011 Segnalazione Share Pubblicato: 21 Maggio 2011 Salve, sono nuovo di questo forum. E da ieri sera che non dormo per cercare una soluzione per resuscitare il mio nokia n8. Ho eseguito un flash con phoenix scaricando il firmware (che ho scoperto essere Vodafone UK)da navifirm ma a un certo punto il programma mi ha dato un errore e da allora il mio nokia si è spento. Tenendo premuto il tasto di avvio ogni tanto da una vibrazione oppure tenendolo premuto ogni tanto ne da tre di vibrazioni. Anche con l'hard reset non riesco a farlo ripartire. Ogni tanto quando collego il caricabatterie al nokia o la usb mi lampeggia il led bianco laterale. C'è un modo per farlo riprendere senza mandarlo in garanzia? vi prego aiutatemi sono stato 11 ore consecutive a pc per cercare una soluzione. Molti dicono che si può usare come ferma carte(spero per te che non sia assolutamente così)...cerca qualche discussione inerente nel forum penso che sia l'unico modo per aiutarti... Link to comment Condividi su altri siti More sharing options...
iFraska Pubblicato: 21 Maggio 2011 Segnalazione Share Pubblicato: 21 Maggio 2011 riflashalo con il death usb Link to comment Condividi su altri siti More sharing options...
paolotrt Pubblicato: 22 Maggio 2011 Autore Segnalazione Share Pubblicato: 22 Maggio 2011 il problema è che quando apro phoenix la spunta dead usb flash è annerita e non la posso cliccare Link to comment Condividi su altri siti More sharing options...
iFraska Pubblicato: 22 Maggio 2011 Segnalazione Share Pubblicato: 22 Maggio 2011 usa questa guida per flasharlo: https://www.nokioteca.net/home/forum/index.php/topic/198044-hack-dei-modelli-piu-recenti-integrazione-di-installserverexe-nel-firmware/ La guida è per l'hack, ma dovrebbe andare lo stesso bene Link to comment Condividi su altri siti More sharing options...
M1rken Pubblicato: 23 Maggio 2011 Segnalazione Share Pubblicato: 23 Maggio 2011 si, infatti la guida va bene, devi usare no connection per avere la possibilità di mettere la spunta a dead usb, diversamente non è possibile. Link to comment Condividi su altri siti More sharing options...
paolotrt Pubblicato: 23 Maggio 2011 Autore Segnalazione Share Pubblicato: 23 Maggio 2011 Product data items list created Backup not required Flashing phone Initializing Scanning image files... Waiting for USB device... 1. Make sure USB cable, Battery and charger are removed from device. 2. Insert USB cable to device 3. Insert Battery to device 4. Insert Charger to device --- Press phone's power button! --- Starting to recover the phone ERROR: Failed to set phone to flashmode Recoverying phone Initializing Scanning image files... Flashing phone Initializing Unable to set the phone to flash mode. Unable to flash. Scanning image files... Waiting for USB device... 1. Make sure USB cable, Battery and charger are removed from device. 2. Insert USB cable to device 3. Insert Battery to device 4. Insert Charger to device --- Press phone's power button! --- Loading secondary boot code: 15168 bytes Secondary boot loaded Loading update server code: 722517 bytes Update server loaded Partitioning.... Partitioning complete Erasing.... Erasing complete Asic CMT: Start programming 183550 KB... Asic CMT: Programming data sent: 0% Asic CMT: Programming data sent: 10% Asic CMT: Programming data sent: 20% Asic CMT: Programming data sent: 30% Asic CMT: Programming data sent: 40% Asic CMT: Programming data sent: 50% Asic CMT: Programming data sent: 60% Asic CMT: Programming data sent: 70% Asic CMT: Programming data sent: 80% Asic CMT: Programming data sent: 90% Asic CMT: Programming data sent: 100% Programming complete WARNING: Asic CMT: NAND status reported bad blocks Asic CMT: programming succeeded Asic CMT: Verifying communication to device... Waiting for communication response: 25 Waiting for communication response: 24 Waiting for communication response: 23 Waiting for communication response: 22 Waiting for communication response: 21 Waiting for communication response: 20 Waiting for communication response: 19 Waiting for communication response: 18 Waiting for communication response: 17 Waiting for communication response: 16 Waiting for communication response: 15 Waiting for communication response: 14 Waiting for communication response: 13 Waiting for communication response: 12 Waiting for communication response: 11 Waiting for communication response: 10 Waiting for communication response: 9 Waiting for communication response: 8 Waiting for communication response: 7 Waiting for communication response: 6 Waiting for communication response: 5 Waiting for communication response: 4 Waiting for communication response: 3 Waiting for communication response: 2 Starting to recover the phone Recoverying phone Initializing Waiting for communication response: 1 Error 0x8401F121 communicating to phone. Unable to verify comm. Warning: Unable to communicate to product after flashing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... ERROR: Unable to detect device 0x8401F145. Check USB connection! ERROR: Product recovery failed! Unable to set the phone to flash mode. Unable to flash. Starting to recover the phone Recoverying phone Initializing Scanning image files... Link to comment Condividi su altri siti More sharing options...
M1rken Pubblicato: 23 Maggio 2011 Segnalazione Share Pubblicato: 23 Maggio 2011 chiudi il programma, riavvia il pc e riprova. che versione di phoenix hai messo? è la 2011? ... la prima parte ha flashato, quindi la cosa in parte ha funzionato .... poi potrebbe anche essere che il cell ha problemi e quindi devi mandarlo in assistenza, però se fai come ti ho descritto puoi averne la conferma. Link to comment Condividi su altri siti More sharing options...
AirSac Pubblicato: 23 Maggio 2011 Segnalazione Share Pubblicato: 23 Maggio 2011 per esperienza personale..sul mio n8 ne ho fatto di ogni..dal downgrade, a cercare di scrivere il fw del c7, ecc..e ti posso dire che questo cell è IMPOSSIBILE farlo morire con il flash. Io lavoro però con una box ( cyclone ) , non con i programmi free. Secondo me hai corrotto la zona SD e per quello il telefono non si accende ( ma se tieni premuto per 10 secondi il bottone di accensione ti fa 3 vibrazioni ). Con una box, la procedura è semplice. Fai un Repair SD e poi un full flash in dead usb modo e alla fine riscrivi un full RPL e vedrai che il telefono torna a funzionare come prima. Con i programmi free è sempre rischioso operare..perchè ma sempre tutto bene..ma la volta che succede qualcosa, non recuperi piu' nulla.. Link to comment Condividi su altri siti More sharing options...
paolotrt Pubblicato: 24 Maggio 2011 Autore Segnalazione Share Pubblicato: 24 Maggio 2011 si si tenendo premuto il tasto di accensione ogni tanto dava le tre vibrazioni...ho provato con jaf ma identica cosa...stamane l'ho mandato in assistenza...sperando che non mi facciano storie...nelle note il nokia center ha scritto spento e basta....io gli ho detto ke si è bloccato e spento da solo e nn si è più riacceso... Link to comment Condividi su altri siti More sharing options...
MassimoFioretta Pubblicato: 24 Maggio 2011 Segnalazione Share Pubblicato: 24 Maggio 2011 si si tenendo premuto il tasto di accensione ogni tanto dava le tre vibrazioni...ho provato con jaf ma identica cosa...stamane l'ho mandato in assistenza...sperando che non mi facciano storie...nelle note il nokia center ha scritto spento e basta....io gli ho detto ke si è bloccato e spento da solo e nn si è più riacceso... tranquillo ho avuto il tuo stesso problema e mandato in assistenza,mi hanno cambiato la scheda interna e chiaramente anche l'imei,la scocca è rimasta la mia,ma non si sono accorti di niente,considerando che è un difetto dell'n8 loro cambiano direttamente senza guardare,cosi mi hanno detto in assistenza e cosi è stato.fammi sapere,ciao, Link to comment Condividi su altri siti More sharing options...
Roger1 Pubblicato: 25 Maggio 2011 Segnalazione Share Pubblicato: 25 Maggio 2011 Speriamo lo cambiano senza problemi. Auguri. Link to comment Condividi su altri siti More sharing options...
M1rken Pubblicato: 25 Maggio 2011 Segnalazione Share Pubblicato: 25 Maggio 2011 sono parecchie le schede madri n8 che vengono mandate al centro per le sostituzioni, molti nokia point non sono nemmeno autorizzati ad aprirli gli n8. Link to comment Condividi su altri siti More sharing options...
paolotrt Pubblicato: 25 Maggio 2011 Autore Segnalazione Share Pubblicato: 25 Maggio 2011 Speriamo ragazzi...speriamo.. Link to comment Condividi su altri siti More sharing options...
pizzi90 Pubblicato: 31 Maggio 2011 Segnalazione Share Pubblicato: 31 Maggio 2011 anche a me è successo oggi la tua stessa identica cosa ho provato a ricollegarlo con il no connection e mi dava errore di comunicazione. come ultima spiaggia ho provato a riavviare il pc il pc ho riprovato e ha funzionato e ora vive..... Link to comment Condividi su altri siti More sharing options...
skyline-leo Pubblicato: 3 Luglio 2011 Segnalazione Share Pubblicato: 3 Luglio 2011 anche a me è successo oggi la tua stessa identica cosa ho provato a ricollegarlo con il no connection e mi dava errore di comunicazione. come ultima spiaggia ho provato a riavviare il pc il pc ho riprovato e ha funzionato e ora vive..... Questo perchè phoenix a 1000 bug ed è SEMPRE stato sconsigliato, ora magicamente tutti lo consigliono.... bha...valli a capire... Link to comment Condividi su altri siti More sharing options...
iFraska Pubblicato: 3 Luglio 2011 Segnalazione Share Pubblicato: 3 Luglio 2011 Questo perchè phoenix a 1000 bug ed è SEMPRE stato sconsigliato, ora magicamente tutti lo consigliono.... bha...valli a capire... perchè forse con jaf non flashi gli S^3? Link to comment Condividi su altri siti More sharing options...
M1rken Pubblicato: 4 Luglio 2011 Segnalazione Share Pubblicato: 4 Luglio 2011 Questo perchè phoenix a 1000 bug ed è SEMPRE stato sconsigliato, ora magicamente tutti lo consigliono.... bha...valli a capire... quindi i centri assistenza usano programmi super buggati? forse è per altri motivi, magari per il fatto che il programma è protetto da copyright nokia mentre JAf è un programma defunto e nessuno reclamerebbe nulla? Link to comment Condividi su altri siti More sharing options...
barrelreacing Pubblicato: 1 Febbraio 2012 Segnalazione Share Pubblicato: 1 Febbraio 2012 per esperienza personale..sul mio n8 ne ho fatto di ogni..dal downgrade, a cercare di scrivere il fw del c7, ecc..e ti posso dire che questo cell è IMPOSSIBILE farlo morire con il flash. Io lavoro però con una box ( cyclone ) , non con i programmi free. Secondo me hai corrotto la zona SD e per quello il telefono non si accende ( ma se tieni premuto per 10 secondi il bottone di accensione ti fa 3 vibrazioni ). Con una box, la procedura è semplice. Fai un Repair SD e poi un full flash in dead usb modo e alla fine riscrivi un full RPL e vedrai che il telefono torna a funzionare come prima. Con i programmi free è sempre rischioso operare..perchè ma sempre tutto bene..ma la volta che succede qualcosa, non recuperi piu' nulla.. salve, riprendo questo post perchè mi ritrovo nella situazione qui descritta, anche io uso cyclone ma non sono ancora riuscito a flashare il mio n8, probabilmente ho utilizzato un firmware inferiore a quello che c'era sul cellu e adesso non si accende più, ho il cavo fbus, ma non riesco a rianimarlo....potresti gentilmente aiutarmi a riprenderlo? prima di flasharlo ho fatto un backup di tutti i certificati e del pm....ti prego se puoi di aiutarmi è una vita che lo uso come fermacarte.....grazie mille...cmqe questo è il log che mi ha dato quando ho tentato di flasharlo: Processing pre flash tasks... Read RPL operation not possible for Old USB Flashing Method Backing up simlock... MCU Version V 92_11w37 MCU Date 14-09-11 Product RM-596 (Nokia N8) Manufacturer © Nokia IMEI ************** Mastercode 2436502454 Simlock backup OK, saved to RM-596_*****************_01022012_11.55.56.SLBackup.PM Backup simlock thread finished, continuing... Pre flash tasks finished, continuing... Processing RM-596_014.002_79.92_prd.core.fpsx (CMT)... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104 CMT_EM_ASIC_ID: 00001040 CMT_EM_ASIC_ID: 00001060 CMT_PUBLIC_ID: 0730010C42DE0344AB0E608CDE38AFBBCCA8E869 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B CMT_BOOT_ROM_CRC: E693EF0D CMT_SECURE_ROM_CRC: AC22615B CMT Ready! RM-596_014.002_79.92_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 Searching for BootCode: DualLine 32Bit (Forcing OLD Protocol) Processing Flash Image Failed -> Not found required Secondary Loader Failed to Process all Image files -> Failed to process RM-596_014.002_79.92_prd.core.fpsx Processing pre flash tasks... Backing up RPL... RPL Creation started... Processing CMT Part... Storing Product Code... Storing PSN... Storing HWID... Trying to store Simlock... Reading Configuration Key... Hashing... Reading SHA1-RSA Signature... Reading SHA1-HMAC Signature... Storing Simlock... Trying to store WMDRM RPL... Reading Keys... Storing WMDRM PD... Reading Security Block... Security block OK and saved to "RM-596_*****************_01022012_11.56.54.SecurityBlock.PM" "0730010C42DE0344AB0E608CDE38AFBBCCA8E869.C0002D9C" Exists, That is good... Storing Additional Data... Checking Superdongle Key... Encrypting Superdongle Key... Storing Superdongle Key... Checking CMLA Key... Storing CMLA Key... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104 CMT_EM_ASIC_ID: 00001040 CMT_EM_ASIC_ID: 00001060 CMT_PUBLIC_ID: 0730010C42DE0344AB0E608CDE38AFBBCCA8E869 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B CMT_BOOT_ROM_CRC: E693EF0D CMT_SECURE_ROM_CRC: AC22615B CMT Ready! Searching for BootCode: DualLine 32Bit RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.24.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND Requested Algorithm: XSR 1.6 (CMT) Searching for BootCode: DualLine 32Bit FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.24.0, Algo: XSR 1.6 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231 APE Subsystem Not Found Flashbus Write baud set to 5.0Mbits Storing NPC... Storing CCC... Storing HWC... CMT VARIANT Not Found Storing PARTNERC... Restarting MCU... RPL Saved OK RPL backup thread finished, continuing... Backing up simlock... MCU Version V 92_11w37 MCU Date 14-09-11 Product RM-596 (Nokia N8) Manufacturer © Nokia IMEI ************** Mastercode 2436502454 Simlock backup OK, saved to RM-596_***************_01022012_11.57.10.SLBackup.PM Backup simlock thread finished, continuing... Pre flash tasks finished, continuing... Processing RM-596_014.002_79.92_prd.core.fpsx (CMT)... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104 CMT_EM_ASIC_ID: 00001040 CMT_EM_ASIC_ID: 00001060 CMT_PUBLIC_ID: 0730010C42DE0344AB0E608CDE38AFBBCCA8E869 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B CMT_BOOT_ROM_CRC: E693EF0D CMT_SECURE_ROM_CRC: AC22615B CMT Ready! RM-596_014.002_79.92_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 Searching for BootCode: DualLine 32Bit RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.24.0, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND Requested Algorithm: XSR 1.6 (CMT) Searching for BootCode: DualLine 32Bit FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.24.0, Algo: XSR 1.6 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231 Flashbus Write baud set to 5.0Mbits Sending Certificates... Certificates OK Partitioning... Partitioning OK Started group flash erase EraseArea[0,CMT]: 0x00040000-0x0007FFFF, ONENAND EraseArea[0,CMT]: 0x000C0000-0x008BFFFF, ONENAND EraseArea[0,CMT]: 0x00DC0000-0x0E97FFFF, ONENAND Erase Partition (CMT) Waiting 320s for erasure finish... Erase taken 0.828s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing CMT ADA Certificate... Writing CMT KEYS Certificate... Writing CMT PRIMAPP Certificate... Writing CMT RAP3NAND Certificate... Writing CMT SOS+PMML Certificate... Writing CMT PASUBTOC Certificate... Writing CMT PAPUBKEYS Certificate... Writing CMT GENIO_INIT Certificate... Writing CMT SOS*UPDAPP Certificate... Writing CMT SOS*DSP0 Certificate... Writing CMT LDSP Certificate... Writing CMT SOS*ISASW Certificate... Writing CMT SOS+CORE Certificate... Writing CMT SOS+ROFS1 Certificate... Programming Status OK! All blocks written OK! Time taken 151.703s Flashing Speed: 7264,66 kBit/S Restarting MCU... Processing RM-596_014.002_79.92_prd.core.fpsx (APE)... Processing RM-596_014.002_01.01_Euro_1_79.92_prd.rofs2.fpsx (CMT)... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104 CMT_EM_ASIC_ID: 00001040 CMT_EM_ASIC_ID: 00001060 CMT_PUBLIC_ID: 0730010C42DE0344AB0E608CDE38AFBBCCA8E869 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B CMT_BOOT_ROM_CRC: E693EF0D CMT_SECURE_ROM_CRC: AC22615B CMT Ready! RM-596_014.002_01.01_Euro_1_79.92_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 Searching for BootCode: DualLine 32Bit RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.24.0, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND Requested Algorithm: XSR 1.6 (CMT) Searching for BootCode: DualLine 32Bit FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.24.0, Algo: XSR 1.6 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231 Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,CMT]: 0x09F40000-0x0DA7FFFF, ONENAND Waiting 320s for erasure finish... Erase taken 0.219s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing CMT SOS+ROFS2 Certificate... Programming Status OK! All blocks written OK! Time taken 51.984s Flashing Speed: 7383,37 kBit/S Restarting MCU... Processing RM-596_014.002_01.01_Euro_1_79.92_prd.rofs2.fpsx (APE)... Processing RM-596_014.002_263.01_IT_CV_79.92_prd.rofs3.fpsx (CMT)... Booting CMT... Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem Processing Flash Image Failed -> Failed to Boot CMT Failed to Process all Image files -> Failed to process RM-596_014.002_263.01_IT_CV_79.92_prd.rofs3.fpsx Link to comment Condividi su altri siti More sharing options...
alexsf91 Pubblicato: 20 Ottobre 2012 Segnalazione Share Pubblicato: 20 Ottobre 2012 ho appena avuto lo stesso problema... potete aiutarmi? Link to comment Condividi su altri siti More sharing options...
M1rken Pubblicato: 21 Ottobre 2012 Segnalazione Share Pubblicato: 21 Ottobre 2012 se esce Failed to Boot CMT -> CMT Not Responding, Phone or Cable problem o è morto un componente del cell oppure il cavo è da cambiare, non c'è molto da poter fare purtroppo. Link to comment Condividi su altri siti More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Accedi Ora